Leading 10 common forklift accidents ， forklift operation should take notice of these matters ！.
Leading 10 common forklift accidents ， forklift operation should take notice of these matters ！.
Blog Article
Don't undervalue the forklift at work. If the operation is not good, there will be severe crashes in minutes, and there are many accidents involving forklifts.
Situation 1: The forklift cargo blocked the motorist's view, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the counterweight, which practically triggered casualties.
Case 3: The width of the forklift freight goes beyond the allowed size of the path and hangs on the roadside rack, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure must take note of these matters ：.
Beginning.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that hinder the safety and security of driving, honk the horn initially and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be safe prior to starting.
3. When the forklift starts with a lots, the motorist should initially confirm that the load is secure and trustworthy.
4. The start needs to be slow and consistent.
Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed doglegs are banned. High-speed doglegs will trigger the lorry to shed lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and need to maintain a particular safety and security range from the lorry ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the tons should not block the chauffeur's sight. In special circumstances, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with health problems or conceal them.
loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or draw. In special scenarios, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch other items or items. The lots should be supported with marginal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable simple positioning of the load and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to utilize forks to choose, transform pallet dump.
Leaving .
1. It is restricted to leave the forklift when the things on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the emergency brake deal with to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, Electric Forklift Truck for Warehouse such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .
Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water must be included.
2. Inspect the security performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be examined and the seals need to be changed in time.
Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be Electric Forklift Truck for Warehouse 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be too sharp to stop the propensity of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or hefty items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal slope greater than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle should be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844